Loading... Please wait...
  • Call us on 978-494-4104
  • My Account
  • Gift Certificates
  • Image 1

JHM Helical Rear Limited Slip Differential, LSD for B6-B7 S4 Auto-Tip Transmission

$795.00
Quantity:
SKU:
JHM-B6B7RearLSDAT

Product Description

INTRODUCING THE JHM HELICAL REAR LIMITED SLIP DIFFERENTIAL!!!

After years of research and development, we are proud to release our JHM Helical Rear Limited Slip Differential (LSD) for the B6-B7 A4 and B6-B7 S4.

Click to enlarge picture

In the stock Audi rear differential, the torque from the motor that's sent to the driveline is evenly divided between the two rear axles. In most driving situations this is normally fine. However, in cases where traction is lost at one wheel (i.e. under hard acceleration out of a corner or launching from a stop) power is only being sent to the spinning wheel. In these situations, a gear-based limited slip differential will take the torque from the wheel that's starting to spin and send it back to the wheel with that's not - the one with better traction. This means that both rear tires will spin together - with or without traction.

Features and Benefits of the JHM Helical LSD:
- Helical gears respond to changes in traction conditions very quickly
- Improves traction and predictability of vehicle behavior: both rear wheels will spin at the same rate. Under hard acceleration out of corners or launching from a stop the car will either "hook up" and go or both rear tires will spin. Some "track focused" drivers say that this allows you to steer the car better with the throttle.
- Prevents "one-legging" (spinning one rear tire only) and therefore eliminates losses in acceleration under load out of corners and heavy acceleration from a stop (launching).
- Maintenance free! There are no clutch packs to replace as they wear out.
- No special gear oil or additives necessary. Again, since there are no clutches, you can run the same gear oil as recommended by Audi in our LSD.
- Our JHM Helical Rear LSD comes with a Limited Lifetime Warranty against manufacturer defects. While we recommend our LSD for anyone looking to improve the traction and predictability of their quattro Audi, the more horsepower your car has or the harder you drive, the more our JHM LSD will make a difference in your car.

Installation Note: When replacing the differential, the factory repair manual states that you must check ring gear backlash and bearing pre-load. Our JHM LSD is built to factory tolerances and all the differentials we have swapped at our service facility haven't required "re-shimming". However, due to variances in factory tolerances, it is best to make sure that these measurements are checked and confirmed. Additionally, if you do not have the right "bearing splitters" to remove your original bearings with a press, install them on the JHM differential, and correctly inspect for wear or issues you may need to replace the differential bearings. If you have concerns about your tools or your ability to properly inspect and/or disassemble and re-assemble your differential please don't hesitate to contact us. We can perform all of this work for you if you send us your differential housing.

FITMENT: The JHM Helical LSD is a direct replacement for OEM differentials with the following part numbers: 01R525121D or 01R 525 121 D. We're working to identify all the cars and differentials our JHM LSD will fit. So far we, have confirmed fitment in Automatic-Tiptronic rear differentials with the following 3 letter codes: GDF. It is important that your car's rear differential has the correct style housing. We have found that some 2007 and up cars have a different style housing that won't accept this version of our LSD. Our current JHM LSD will fit in the differential cases that are black and have a cover for the case that bolts on to the side of the housing to get the differential out. If your differential has the newer style, aluminum case that has the cover on the rear of the case, this version of our JHM LSD will NOT work for your car. We are working on a solution for these later style differentials as well as others based on customer inquiries and market demand.
- 2003 to 2005 B6-S4 Automatic-Tiptronic transmission and quattro
- 2005.5 to 2009 B7-S4 Automatic-Tiptronic transmission and quattro

**NOTE THE EXCEPTION ABOVE FOR 2007 AND UP DIFFERENTIAL CASES**

**Don't forget to add axle seals and gear oil to your order before you check out!**
For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout.

Fitment:
Note: JHM works hard to make all fitment charts as accurate as possible please read the product description to make sure this is correct for your vehicle.
Make Model Year Range
Audi S4 - B6 2003 - 2005
Audi S4 - B7 2005 - 2009

Find Similar Products by Tag

Product Reviews

Write Review

This product hasn't received any reviews yet. Be the first to review this product!